bubba bought a biggie. WAY TOO biggie, matter of fact.
model "enco 1000" made in taiwan. 2hp motor, infinitely variable speed, 230 volt three phase, table tilts (all four ways: forward, back, left and right). has blade WELDER and annealer, too. grinds the blade too, is my understanding. and an 'air puffer' that blows the chips off your cut line. it's all there. it's dusty. it needs four new tires, and a general cleanup. it weighs 1700 lbs
NOT stored at my location, but I *am* the owner. will provide any type receipt or bill of sale you want. can 'probably' load the thing up for you (inquire first). no asking price, it must go, I'm not insane though.
prefer to sell outright, but will also 'partial swap' for stuff on my wants list (or maybe other stuff). might even swap it outright for something of extreme grooviness.
spec's online, photos online, 'comparable' saw pix with spec's online, movie of it online, see it in ALL its glory here:
>bubba bought a biggie. WAY TOO biggie, matter of fact.
>model "enco 1000" made in taiwan. 2hp motor, infinitely variable speed, >230 volt three phase, table tilts (all four ways: forward, back, left >and right). has blade WELDER and annealer, too. grinds the blade too, is >my understanding. and an 'air puffer' that blows the chips off your cut >line. it's all there. it's dusty. it needs four new tires, and a general >cleanup. it weighs 1700 lbs
>NOT stored at my location, but I *am* the owner. will provide any type >receipt or bill of sale you want. can 'probably' load the thing up for >you (inquire first). no asking price, it must go, I'm not insane though.
>prefer to sell outright, but will also 'partial swap' for stuff on my >wants list (or maybe other stuff). might even swap it outright for >something of extreme grooviness.
>spec's online, photos online, 'comparable' saw pix with spec's online, >movie of it online, see it in ALL its glory here:
>e-mail links on site, bottom center of every page
>thanks,
>dave
Where are you located?
And your website is "under review"...no pictures are available.
Gunner
"IMHO, some people here give Jeff far more attention than he deserves, but obviously craves. The most appropriate response, and perhaps the cruelest, IMO, is to simply killfile and ignore him. An alternative, if you must, would be to post the same standard reply to his every post, listing the manifold reasons why he ought to be ignored. Just my $0.02 worth."
> On Sat, 07 Nov 2009 17:09:35 -0500, dave <tool_...@weirdstuffcox.net> > wrote:
>>bubba bought a biggie. WAY TOO biggie, matter of fact.
>>model "enco 1000" made in taiwan. 2hp motor, infinitely variable speed, >>230 volt three phase, table tilts (all four ways: forward, back, left >>and right). has blade WELDER and annealer, too. grinds the blade too, is >>my understanding. and an 'air puffer' that blows the chips off your cut >>line. it's all there. it's dusty. it needs four new tires, and a general >>cleanup. it weighs 1700 lbs
>>NOT stored at my location, but I *am* the owner. will provide any type >>receipt or bill of sale you want. can 'probably' load the thing up for >>you (inquire first). no asking price, it must go, I'm not insane though.
>>prefer to sell outright, but will also 'partial swap' for stuff on my >>wants list (or maybe other stuff). might even swap it outright for >>something of extreme grooviness.
>>spec's online, photos online, 'comparable' saw pix with spec's online, >>movie of it online, see it in ALL its glory here:
'North Central Florida' covers over 25% of the state but his IP address resolves to Gainesville. No telling how accurate that is, since it is assigned to Cox Cable. My IP address shows me about a two hour drive from where I live.
> ATP* wrote: >> Gunner Aschwrote: >>> Where are you located? >> north central florida
whoa! I'm in gainesville, however the saw is in alachua florida. site says so (who would've expected to post a site, test it as working and answering, *then* have it 'go down' an hour later with that 'under review' nuisance. brand new host today, 1st site posted there. these 'free site hosts' can be *QUITE* the huge nuisance, and always for some totally Unexpected reason...
meanwhile, here's an ALTERNATE location: same exact site, on a different host (also tested working, as of time of this post)
>>>bubba bought a biggie. WAY TOO biggie, matter of fact.
>>>model "enco 1000" made in taiwan. 2hp motor, infinitely variable speed, >>>230 volt three phase, table tilts (all four ways: forward, back, left >>>and right). has blade WELDER and annealer, too. grinds the blade too, is >>>my understanding. and an 'air puffer' that blows the chips off your cut >>>line. it's all there. it's dusty. it needs four new tires, and a general >>>cleanup. it weighs 1700 lbs
>>>NOT stored at my location, but I *am* the owner. will provide any type >>>receipt or bill of sale you want. can 'probably' load the thing up for >>>you (inquire first). no asking price, it must go, I'm not insane though.
>>>prefer to sell outright, but will also 'partial swap' for stuff on my >>>wants list (or maybe other stuff). might even swap it outright for >>>something of extreme grooviness.
>>>spec's online, photos online, 'comparable' saw pix with spec's online, >>>movie of it online, see it in ALL its glory here:
>>>e-mail links on site, bottom center of every page
>>>thanks,
>>>dave
>> Where are you located?
>north central florida
Damn. Sigh
Nice looking saw. Be nice to have in the shop.
Damn........sigh......
Gunner
"IMHO, some people here give Jeff far more attention than he deserves, but obviously craves. The most appropriate response, and perhaps the cruelest, IMO, is to simply killfile and ignore him. An alternative, if you must, would be to post the same standard reply to his every post, listing the manifold reasons why he ought to be ignored. Just my $0.02 worth."
> Yes. It's a little over 60 miles from me, but I'm sure it's not in my >budget. :(
I wonder if he would donate it and take the credit on his taxes?
"IMHO, some people here give Jeff far more attention than he deserves, but obviously craves. The most appropriate response, and perhaps the cruelest, IMO, is to simply killfile and ignore him. An alternative, if you must, would be to post the same standard reply to his every post, listing the manifold reasons why he ought to be ignored. Just my $0.02 worth."
|
